Hi,
Post by John DavidHi Christian,
Thanks for your reply,
I wanted to use Adafruit Fingerprint sensor which can be connected to
Arduino Uno micro-controller with TTL serial. Then I will connect the
Arduino to the i.MX53 QSB via USB. Here you can find the
Adafruit-fingerprint-sensor-library
<https://github.com/adafruit/Adafruit-Fingerprint-Sensor-Library>.
Well, we do not have USB host controller support for the i.MX53 yet. So
in this case you will need to first port that driver.
Alternatively, and maybe less complicated would be to connect the
Fingerprint sensor directly to a second UART of the i.MX53 QSB. AFAIK
there are two additional UARTs available via the expansion header (j13).
Of course you would need a corresponding connector[1], and propably have
to configure the IOMUX controller within our platform driver
appropriatedly to use the additional UART.
In the end you have to port the Fingerprint sensor library.
Post by John DavidIt would be also great if you might have other fingerprint sensors that can
be used integrated with the i.MX53 QSB board running Genode.
I'm not sure what you mean with "integrated". AFAIK there is no
fingerprint sensor on this board available, or is it?
Regards
Stefan
[1] In the Hardware manual I've found this paragraph:
"The proper connector to mate with Expansion Port J13 is made by Samtec,
QTH‐060‐XX‐L‐D‐A, where XX determines the height of the connector."
Post by John DavidThanks,
John
On Thu, Jun 9, 2016 at 12:48 PM, Christian Helmuth <
Post by Christian HelmuthHello John,
Post by John DavidI am running Genode on i.mx53 QSB and was wondering to use a fingerprint
scanner such as Adafruit finger print reader to create a virtual
fingerprint. Is there any a device driver and library in Genode for a
fingerprint scanner? Could you please tell me how to use it? Thanks in
advance.
Please provide more information about the device you like to connect
to the i.MX53 QSB. Is it a USB device or connected by other means? How
does Linux drive the hardware device? Does it just need a low-level
driver or are additional libaries required?
Regards
--
Christian Helmuth
Genode Labs
http://www.genode-labs.com/ · http://genode.org/
https://twitter.com/GenodeLabs · /ˈdʒiː.nəʊd/
Genode Labs GmbH · Amtsgericht Dresden · HRB 28424 · Sitz Dresden
Geschäftsführer: Dr.-Ing. Norman Feske, Christian Helmuth
------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and
traffic
patterns at an interface-level. Reveals which users, apps, and protocols
are
consuming the most bandwidth. Provides multi-vendor support for NetFlow,
J-Flow, sFlow and other flows. Make informed decisions using capacity
planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e
_______________________________________________
genode-main mailing list
https://lists.sourceforge.net/lists/listinfo/genode-main
------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are
consuming the most bandwidth. Provides multi-vendor support for NetFlow,
J-Flow, sFlow and other flows. Make informed decisions using capacity
planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e
_______________________________________________
genode-main mailing list
https://lists.sourceforge.net/lists/listinfo/genode-main
--
Stefan Kalkowski
Genode Labs
http://www.genode-labs.com/ · http://genode.org/